: Датчик положения руля


BMW E39: бампер Нижний Новгород



Overcast day
03.08.2014, 11:50
Размещу в открытом разделе на всякий случай.

I had error code 0B/wrong LWS-ID under the LEW menu in PA Soft, and the standard 5E43 error for SAS under ABS system.

Clearing the codes did nothing, they just popped up immediately, searching for "wrong lws-id" was equally a waste of time.. logically I figured it to be just not coded for the vin, as the errors popped up immediately after clearing them over and over.

The solution, pretty simple, I pulled the EEPROM off my other e46, and after seeing what it looked like it was obvious.

1) Open PA Soft 1.4, connect to car, click on LEW to open the LEW page
2) Click Reprogramming
3) On the Reprogramming menu, Click Write ADFG
4) Enter "00XXXX" where XXXX is the last 4 digits of your VIN
5) Click OK

Once that completes

6) Click Read EEPROM
7) Edit the values highlighted in the attached image

You will need a hex to ansi converter for 2 letters
-- this appears to be a simple converter that works well
http://www.dolcevie.com/js/converter.html
--

The row we are modifying is 0x20, looking specifically at locations 4-8 (red text in the image)

This would be 20 45 31 4A 4C in the image below

These characters translate to the last 7 VIN digits, backwards.

4C in hex converts to the letter L
4A in hex converts to the letter J
31, 45, 20

This would be the last 7 of the vin LJ31452

Change for your vin.

8) Click the Save Icon
9) Click Write EEPROM
10) once this completes, clear the errors under both LEW and ABS pages

DOPE
03.08.2014, 12:59
добавлю,что это кодирование нового датчика под машину с последующей инициализацией с помощью PA Soft

DOPE
13.08.2014, 11:09
Чтобы провести инициализацию с помощью INРA,необходимо сделать следующие действия

1.Идем в папку C:\EC-APPS\INPA\CFGDAT и редактируем файл SONDER.ENG - добавляем в самом конце:
ENTRY=,,
ENTRY=,,
ENTRY=lws_abgl,Steering Angle Adjustment

2.Добавить файлы тынц (http://my-files.ru/40baon) в папку C:\EC-APPS\INPA\SGDAT

Заходим в INPA,нажимаем Special Test (F9),выбираем пункт Steering Angle Adjustment,загружается синий экран,нажмаем Tune (F6),блокируем руль выставленный в нулевое положение,подтверждаем действие (F5),в ходе инициализации вылезет 2 ошибки-не обращаем внимания
Готово:)

Артур270604
14.08.2014, 13:58
Слушай, откуда ты это всё знаешь?

DOPE
14.08.2014, 14:43
Слушай, откуда ты это всё знаешь?

я учусь понемногу)информация есть,но многое самому приходиться додумывать-никто разжевывать не будет

Overcast day
14.08.2014, 22:55
Макс - подающий надежды. Жаль, что Антоха далеко, а то бы вы спелись бы.

ARA
15.08.2014, 00:08
Пусть Антонио его дистанционно обучает, нам это всем нужно.

Артур270604
15.08.2014, 14:24
Пора открывать вечерние курсы и обучать нас всех неведующих)))